Vonets Vap11g Drivers Download

The VAP11G-300 is a unique device with a fixed ethernet to wireless bridge that helps in situations where:

Vonets vap11g-300 Posted on December 16, 2015 by hanso The VAP11G-300 is a unique device with a fixed ethernet to wireless bridge that helps in situations where. Download and run the executable; Follow the instructions on the screen. The installation applet will automatically detect the operating system and install the correct drivers; The WinPcap-based applications are now ready to work; To remove WinPcap from the system, go to the Control Panel, click on 'Add/Remove programs' and then select 'WinPcap'. VONETS——VAP11N 150M Mini WIFI Bridge 3 Chapter 1 Quick Setting Guide 1. Connect the computer Set computer IP address to automatically, please see the words in the red circle of the. VONETS VAP11G WIFI BRIDGE DRIVER DOWNLOAD - I like these Vonets products. Pages with related products. It rebooted and within 3 minutes I had an Ethernet connection through dhcp IP. Learn more about Amazon Giveaway. I can move this device to any device in my house that needs a wireless connection but doesn't have hardware. Learn more about Amazon Prime.

  • You want a fixed ethernet connection, but none is available at the location.
  • Wireless is available, but the device either has no wireless capabilities.
  • A wireless capability can be added but to configure it, a working network connection is required.
  • USB ports are scarse.
  • Wireless USB adapters are too powerhungry.
  • You want two wireless devices to communicate without a wireless router available.


The VAP11G-300, with a size comparable to the Raspberry, has two cables: a USB power cable USB A and an ethernet cable with the RJ45 connector.
A powerjack is also availlable. Status leds show its operation.

Drivers

With the VAP11G-300 the WiFi intelligent bridge function one can just plugin the ethernet cable, and the device functions as a transparant bridge via wireless to the network. Perfect to configure the Raspberry Pi B’s headless or to avoid the often troublesome and powerhungry wireless adapters taking up an USB connector.

Besides the bridge function it can also function as a wireless repeater or a wireless accesspoint. The latter are not unique, the bridge function is.

Download

Configuration

The device is quite simple to setup. The device in factory default setting or after a hard reset functions as a wireless acccesspoint with a configuration webpage.
Turning it on by plugging the USB power cable in a supply or plug a powercable in the powerjack of the device and, from a PC or tablet or phone look for the SSID VONETSXX.
Connect to the open Access point and enter the url http://vonets.cfg.
With some clear configuration steps the VAP11G-300 can be connected to your wireless network.

The default is to function as wireless repeater + bridge, the repeater function can be disabled. Once this is done and the device rebooted the ethernet cable functions as a fixed ethernet connection.

Hardware Spec

Protocol StandardIEEE 802.11g, IEEE 802.11b, IEEE 802.11n
Rate of transmission 300Mbps
Interface 1 DC2.0 power hole;
1 dedicated two in one power supply cable, with a set of power supply and a set of 10/100M
adaptive Ethernet cable;
Button Reset button (long press 5 seconds)
LEDStatus instruction:
WiFi state/Hot spot connection state ( blue light);
Ethernet port state(light green for success);
Antenna Built-in 2pcs Smart omnidirectional 2dbm Antennas
Size 90mm x 45mm x 15mm(L x W x H)

Vonets Vap11g Drivers Download Windows 7

Wireless Related

Basic FunctionChannel option: 1-14;
WiFi Hot spot scan automatically;
WiFi Hot spot memory;
WiFi Hot spot switches.
Working ModeWiFi intelligent repeater mode:
Repeater mode (WiFi signal repeater), it can extend the distance of WiFi transfer;
Wireless Security64/128/WEP encryption
WPA-PSK/WPA2-PSK、WPA/WPA2 security mechanism
System FunctionRestart device
Reset factory
Administrate account and password revise
Firmware upgrade

Vonets Vap11g Driver Download

Related posts: